Q&A Community - JLCPCB

Hello, Amphenol 59453 (SFVL) series require locking notches like these. Can you manufacture these?

1 Reply Asked by 26*******6A

Minimum spacing between electrical conduction tracts and heatsink pads on copper core PCBs

The minimum spacing for traces is 0.1mm. How much space must there be between a heatsink pad on copper core PCBs and a “no......

1 Reply Asked by 84*******0A

3D Barcode from batch to batch

If I want a repeat order, how do I amend the unique number inside the 3D barcode?

1 Reply Asked by 22*******0A

PCB outline bit size

Hi - I'd like to put some fine details on my board outline. What is the router bit size used to cut the board outline for ......

1 Reply Asked by 26*******2A

What does "Assembly difficulty" mean?

Some components has "Assembly difficulty" section in its page, but I'm not sure what "Assembly difficulty" means. Does thi......

1 Reply Asked by 79*******2A

ENEPIG Finish

Do you offer ENEPIG Finish?

1 Reply Asked by 49*******2A

Blind Via Support

Do you support blind vias in your PCB manufacturing process?

3 Replies Asked by 81*******3A

paste on unpopulated pads

how to apply solder paste to all smd pads, including pads with no component to place

1 Reply Asked by 43*******3A

Slot holes for RCA jack in EAGLE footprint

Attached is the footprint of a RCA jack. The yellow pads (in Dimension layer) over solder pads are the slot holes for foot......

1 Reply Asked by 63*******2A

V-countersink hole

I found the following information: https://www.jlc.com/portal/q6i44031.html Will JLCPCB also support V-countersink hole so......

1 Reply Asked by 85*******5A

Silkscreen over pads

Hello! I have a question, in my design I put some silkscreen on a pad that does not have copper on the front layer. The Ki......

1 Reply Asked by 90*******3A

Expose Aluminium on a Aluminium PCB

Short Version: Can we expose the Aluminium core of a Aluminium PCB to a surface? And if so, how? Is there a Gerber layer w......

1 Reply Asked by 23*******7A

Panel Size

Hello, I am looking for producing panels and I couldn't find information of what would be the maximum size (area) of a pan......

1 Reply Asked by 92*******3A

V-Cut and actual PCB dimention

When I put a V-Cut line or text on the outline layer, the PCB uploader calculates larger dimensions than the actual size. ......

1 Reply Asked by 24*******9A

Detect Isolated Unconnected Vias Warnings

I have a problem with the DFM analysis reporting warnings from the "Detect Isolated Unconnected Vias" check. There are fou......

1 Reply Asked by 87*******6A

different silk screen on order

Hello, is it possible to have a different silkscreen on this order if i reorder like this order W202411160047293 ? we need......

1 Reply Asked by 32*******8C

THT parts not soldered but included in package

Hello, i want to order PCB with assembly for SMD parts and i want to solder THT parts myself. Is there an option that thos......

1 Reply Asked by 76*******8A

Hole size in mm and thou

Hi, in my design, i used some holes at metric dimensions and some holes are at imperial system. Below is the current summa......

1 Reply Asked by 89*******5A

USB Flex Cable impedance control

I'm going to make a USB extension cable with FPC. I want the impedance of the working pair to be 90ohms. Please let me kno......

1 Reply Asked by 74*******3A

Dimensions

How can I be sure (in Eagle) if the dimentions of my board are up loaded?

1 Reply Asked by 23*******5A

Q&A Community - JLC3DP